Product Description:
Features: 1.Easy to operation. 2.Low cost, high practicality. 3.High quality of alloy steel that can maintain each lubrication point with oil. 4.The length of L can be customized. Standard length is steel tube 300 mm.
1.Fixed amount of oil feeding. The lubrication points of volume distributor supply a fixed flow of lubricant. The discharge volume of each outlet is 0.18 cc/stroke.
2.Every piston of CV type progressive feeders cannot deliver its lubricant until the preceding one has discharged it.
3.If one feeder section doesn't receive any lubricant or is blocked, the entire CV type progressive feeder will stop, and that situation can be noticed by the signal of the feeder.
4.The standards are assembled detective piston, which can be seen if operation is normal.
1.CENA type has a timer, which controls the operation and interval time. It has operation, abnormal and interval indicators that is easy for visual checking. 2.It has a pressure-regulating valve, which can adjust the pressure. 3.It has a pressure gauge that can detect the pressure easily. 4.It has a float switch (NC Contact) that can detect the oil volume. When oil is lower than the minimum level, the float switch will send continuous signal automatically. 5.It has a reset button (RES button), press the button, and it would return to the original setting time and start the cyc
Product Description:
Features: 1.Fixed amount of oil feeding. The lubrication points of volume distributor supply a fixed flow of lubricant. 2.T and CDB type have many kinds of discharge volume to be chosen: 0.1, 0.2, 0.3, 0.4, 0.5 cc/stroke. As ordering, please details the discharge volume wanted. 3.The standards are assembled detective piston, which can observe if operation is normal. 4.CDB, T type volume distributors have to work with pressure-relief type lubricators, and lubricant will feed during the interval time of the lubricator. 5.T type could be assembled NO (Normal Open) or NC (Normal Close) senso
Product Description:
Features: 1.CLHA type has good tight pressing iron, which can press grease out smoothly. 2.Low cost, and high practicality. 3.Easy to be operated by pushing the handle down for oil feeding. 4.Small size and easy for installation. 5.CLHA type is suitable for grease NLGI grades 0 to 000,and CLHP type is suitable for grease NLGI grades 0 to 2. 6.Recommend using a grease gun for filling with lubricant from grease inlet. It can avoid air or impurities dropping into the reservoir. 7.Fill the lubricator with grease to exhaust air before the distributors are mounted.
Product Description:
Features: 1.According to the difference of flow rate, there are CLS-10, CLS-30, CLS-50 type, among them, CLS-50 has largest flow rate 4.5 L/min, please refer the specification for details. 2.CLS type is circulating lubricator, which means the oil flows out, then comes back into the oil tank through the cyclic inlet. The cyclic inlet has magnetic filter, which can block the impurities and assure the oil clean. 3.After installing and connecting the piping, feed oil till oil flows out, then start to use this lubricator. 4.It used a high quality pump that not only has steady output pressure a
Product Description:
Features: 1.CEF type is circulating lubricator, which means the oil flows out, then comes back into the oil tank through the cyclic inlet. The cyclic inlet has magnetic filter, which can block the impurities and assure the oil clean. 2.The timer controls the operation and interval time. The electronic box has operation, interval and abnormal indicators. 3.It has a feed-oil button, press the button and the oil will feed immediately. 4.After installing and connecting the piping, press the ¡§feed-oil button¡¨ till the oil flows out, then start to use it. 5.It used a high quality alloy steel ge
Product Description:
Features: 1.Fixed amount of oil feeding. The lubrication points of volume distributor supply a fixed flow of lubricant. 2.CAB type has many kinds of discharge volume to be chosen: 0.03, 0.06, 0.10, 0.16 cc/stroke. As ordering, please details the discharge volume wanted. 3.CBB type also has many kinds of discharge volume to be chosen: 0.1, 0.2, 0.3, 0.4, 0.5 cc/stroke. As ordering, please details the discharge volume wanted. 4.CAB, CBB type volume distributors have to work with pressure-relief type oil lubricators, and oil will feed during the operation time of the lubricator.
Product Description:
Features: 1.CLA type is divided by the volume of container CLA-6(350cc) and CLA-8(600cc). 2.Low cost, high practicality. It can be used in diverse machinery. 3.Easy to be operated by pushing the handle down for oil feeding. 4.Small volume and easy to install. 5.The unit is equipped with reverse stopper that prevents the back-flow of oil. 6.It has an oil outlet on left or right side of the unit. A dual outlet (left and right sides) is also available. Application of Machines Equipment: 1.This unit can work with the machines that do not need to feed oil at certain time. 2.It's suitable
Your search for " " has found productsgearpump548_s.jpg)
progressivefeeders111_s.jpg)
electriclubricator56_s.jpg)
pressurerelieftypeoillubrication57412_s.jpg)
greasemanuallubricator785_s.jpg)
circulatingelectriclubricator0587_s.jpg)
circulatingelectriclubricator123_s.jpg)
resistancespraygun2987_s.jpg)
typevolumedistributor0897_s.jpg)
.jpg)
